West Fork Logging Co.; Spar Pole. One of the ways to get logs from a remote location to the railroad car was the use of "High Lead" logging. It involved a main cable passed from the engine drum of a "donkey" through a block at the top of a tall spar tree (or pole.) A spar was a 150 to over 200 foot tree with the branches trimmed away and the top lopped off by a "high climber." The cable, powered by the steam donkey, could then be used to pull the logs to the dump. West Fork Logging was located in Mineral in Lewis County and had an office in the Tacoma Building. L.T. Murray was the president and H.E. Post was the secretary. G75.1-091
West Fork Logging Co. (Mineral); Lumber industry--1920-1930;
In March of 1920, a steam donkey on a sled was photographed for the West Fork Logging Co. The donkey was used for pulling logs in from the woods. In its simplest form, a donkey was just a steam engine with a drum and a steel cable. The winch was used to pull in logs or load them. In this case, the boiler is mounted, along with the drums, on a sled to make the unit portable. The steam donkey replaced the logging horses and oxen with the power of steam. It was faster, cheaper and more reliable than animals. The West Fork Logging Co. was located in Mineral, about 14 miles north of Morton in Lewis County. It was owned and operated by L.T. Murray. G75.1-093; TPL-9856 (Labbe & Goe, Railroads in the Woods)
On March 5, 1920, cameras rolled as the electric powered "Olympian" pulled out from Tacoma and made history. This marked the formal opening of the Cascade division for electrically operated trains driven by 3000-volt current supplied by the glacier streams of the Cascades. Over 100 guests from Tacoma and Seattle (railroad officials, newsmen and politicos) were aboard a special pilot train that preceded the Olympian. The Olympian made its maiden electric powered ascent through the passages of the snow draped Cascades to its summit where the special train was sidetracked so the Olympian could continue on to Chicago. The special train would travel to Cle Elum and back to Tacoma. The Chicago, Milwaukee & St. Paul train reached speeds up to 60 mph with barely any effort and without puffs of black smoke. It descended as smoothly as it ascended, proving that cross country electrical trains were viable. G44.1-080 (TDL 3/6/1920, pg. 3; TNT 3-6-20, p. 1) TPL-2376
Railroad cars--Tacoma; Railroad locomotives--Tacoma; Railroad companies--Tacoma; Chicago, Milwaukee & St. Paul Railroad Co. (Tacoma); Railroads--Tacoma--1920-1930;
Chicago, Milwaukee and St. Paul Railroad, Engine #10254. On an official test trip in March of 1920, a brand new Bi-polar engine pauses for some publicity shots. The class EP2 engine was manufactured by Alco-GE. The bi-polars were unique in design because the bi-polar fields for each motor were carried on the truck frame. The huge 265 ton, 3,240 hp bi-polars were designed specifically for passenger service in the Cascades and were an immediate success when put into service in 1920. Their top speed was rated at 70 mph and they could pull 1, 120 tons (14 cars) up a 2% grade at 25 mph. The electric locomotives were also unique in appearance, riding low on 44" drivers, and in sound, their trademark a distinctive high pitched shrill from their air whistles. (Charles and Dorothy Wood "Milwaukee Road West") G44.1-079, TPL-2379
Railroad locomotives--Tacoma; Railroad cars--Tacoma; Railroads--Tacoma; Chicago, Milwaukee & St. Paul Railroad Co. (Tacoma);
Side view of parked St. Paul & Tacoma Lumber Co. No. 1 truck filled with stacks of what may be plywood. This April, 1920, photograph may have been taken at the company's downtown Tacoma yard. As noted through the doorless truck, there was no driver at the wheel. G36.1-160
St. Paul & Tacoma Lumber Co. (Tacoma); Trucks--1920-1930;
St. Paul & Tacoma lumber yard. This November, 1920, progress photograph shows a fuel conveyor belt being constructed 24 feet above the ground at the St. Paul & Tacoma Lumber Co. Two 2 ton locomotive cranes are pictured lifting a 106 foot truss into place. The 641 foot long aerial belt will run from the mill to a point on the waterway directly across from the Consumers Central Heating Co. The conveyor belt will be used to transport the mill's waste wood, formed into logs. The fuel will be dumped on barges and carried across to the heating plant where it will be burned to supply heat to the city. The conveyor belt was all wood with the exception of the belt itself and the roller bearings. Parallel chord lattice was used for the entire length with the exception of street crossings where 106 foot span Belfast type lattice trusses were used. (TDL 1/9/1921, pg. 6) TPL-2047; G36.1-163
Lumber industry--Tacoma--1920-1930; St. Paul & Tacoma Lumber Co. (Tacoma); Belts & belting (Equipment); Fuel trade--Tacoma--1920-1930;
ca. 1920. Copy of Asahel Curtis print #51689 requested by the Washington State Historical Society on June 1, 1977. View of unidentified male and female along side of train. The couple are wearing railroad caps. The man is wearing a white shirt and striped tie under his somewhat soiled uniform.
ca. 1920. Chicago, Milwaukee and St. Paul Railroad, Engine #10253. This is an Asahel Curtis print, #46216, which was requested copied by the Washington State Historical Society on April 1, 1977. Three men are standing next to the electric powered engine, spaced far apart, with the man in the foreground seemingly prepared to give the "go ahead" signal. Photographer Curtis documented industry in Washington State as well as historic events and geographic features. He was based in Seattle and worked there until his death in 1941. 60,000 of his images are held in trust by the Washington State Historical Society. (www.wshs.org/wshm/online-exhibits/curtis/exhibitb.htm)
Railroad locomotives; Railroad cars; Chicago, Milwaukee & St. Paul Railroad Co.; Railroads;
ca. 1920. Chicago, Milwaukee and St. Paul Railroad, Engine #10254. Copy of Asahel Curtis print #52236 requested by the Washington State Historical Society on June 1, 1977. The electric powered train pauses on the tracks circa 1920. This is one of the 60,000 Asahel Curtis images in the Washington State Historical Society collection.
Railroad locomotives; Railroads; Railroad tracks; Chicago, Milwaukee & St. Paul Railroad Co.;
ca. 1920. Chicago, Milwaukee & St. Paul Railroad, Engine #10252. Copy of Asahel Curtis print #51601 requested by the Washington State Historical Society on April 1, 1977. The electric powered train may have been departing/arriving at the Chicago, Milwaukee & St. Paul Tacoma location. The Washington State Historical Society has 60,000 Curtis images in its collection.
Railroad locomotives; Railroads; Chicago, Milwaukee & St. Paul Railroad Co.;
ca. 1920. Ship under construction or being repaired at Skansie Shipbuilding Co. yard at Gig Harbor, circa 1920. Skansie Brothers was founded in 1912 by four Yugoslavian brothers, Pete, Mitchell, Andrew and Joe Skansie. TPL-688, BU-13900
ca. 1920. A fan of Columbia Brew, a "near beer" produced by the Columbia Brewing Company, models a suit for not-just-any occasion. The jacket and pants have been made by pasting labels for Columbia Brew on pants and a striped shirt. The top hat also displays an enlarged label for Columbia Brew. The Columbia Brewing Company opened their brewery on South C Street between South 21st and South 23rd in 1900. They made "Columbia Brew" during the dry period of prohibition. Columbia Brewing Co. was purchased by Heidelberg Brewing Co. in 1949; which was purchased by Carling Brewery in 1959. The plant closed in 1979. (Copies of old prints ordered by Heidelberg Brewing Company in December 1954.) Format 6" x 8". TPL-5565
Brewing industry--Tacoma--1910-1920; Columbia Brewing Co. (Tacoma); Costumes; Prohibition--Tacoma;
ca. 1920. Smelter operations at ASARCO. Steam rises as ore is poured via hoisted ladle onto giant cylinders at the American Smelting & Refining Co.'s plant in Ruston circa 1920. Other large ladles are on the floor waiting to be filled with ore. TPL-899; G37.1-184
American Smelting & Refining Co. (Tacoma); Smelters--Tacoma--1920-1930; Industrial facilities--Tacoma--1920-1930;
ca. 1920. Smelter operations at ASARCO. These employees of the American Smelting & Refining Co. (ASARCO) are carefully monitoring what may be the pouring of molten ore in this circa 1920 photograph. It seems to have caught the attention of several other workers in the area. TPL-2351; G37.1-191
American Smelting & Refining Co. (Tacoma); Smelters--Tacoma--1920-1930; Industrial facilities--Tacoma--1920-1930;
An unidentified mill in Tacoma's Tideflats was photographed by Marvin Boland in March of 1921. No workers are in sight. Piles of lumber are stacked throughout the yard. G36.1-043
On September 2, 1921, a steam powered cargo ship from the Luckenbach Line was docked at the Tidewater Mill, 3901 E. 11th St. The Tidewater had been opened in 1918 and was capable of producing 100,000 board feet a day. The majority of its products were shipped for export. The mill was built with a frontage of 750 feet of deep water, allowing the company to load several vessels at a time. The Luckenbach Steamship Co., 1850-1974, was one of the longest-lived and most successful U.S. shipping companies. It was started in 1850 by Lewis Luckenbach and grew to be a major force in intercoastal trade. (TDL 12/22/1918, pg. B-8; www.nationalflaggen.de) G49.1-074
The Tidewater Mill, on the east side of the Hylebos Waterway, was photographed on September 2, 1921 as the large steamship "Quinault" was being loaded with timber. The mill was built in 1918 on six acres of soggy land purchased from Gen. James Ashton. The land was filled in and the mill was built. It was one of only a handful on the Pacific Coast capable of producing the longest timbers. Tidewater could cut timbers up to 130 feet in length. The mill site's major advantage was 750 feet of deep water moorage, allowing the loading of several vessels at a time. (TDL 12/22/1918, pg. B-8) G49.1-071; TPL-9251
This elevated view of the Buffelen Lumber & Manufacturing Company, looking toward Tacoma across the Tideflats, was captured in November of 1921. The narrow bridge built on pilings is the old Hylebos Creek bridge. Located in the industrial Tideflats at Lincoln Ave. & Taylor Way, the sprawling Buffelen plant had been undergoing rapid expansion with the construction of a new warehouse in 1916 and a new power plant five years later. Other important improvements in 1921 included dry kilns and warehouses. Buffelen was organized in 1912 by John Buffelen primarily as a door manufacturer. In 1916 the company started to manufacture fir plywood. A small ad placed in the Tacoma Daily Ledger on 7-11-21 listed "fir doors, 3-ply panels, alder panels, sash, etc." as products manufactured by the firm which had offices in Minneapolis and Tacoma. (TDL- Ad 7-11-21, p. 7; Tacoma Sunday Ledger, 1-1-22, B-5-article)
Construction on the new John Dower Lumber Company headquarters building at 733 East 11th Street began in late November, 1921. The company held an open house for the general public on March 11, 1922. The building, designed by Bullard & Mason, was one of the most unique lumber offices in the country. The finish on the exterior was designed to resemble a log house; the interior was finished in selected native woods, stained and varnished to bring out their natural colors. In 1922 the John Dower Lumber Company was one of the largest retail lumber companies in the United States. The St. Paul & Tacoma Lumber Company purchased the Dower yard and headquarters building in 1942. BU-11057
Lumber industry--Tacoma--1920-1930; John Dower Lumber Company (Tacoma); Building construction--Tacoma--1920-1930;
Elevated view of Tacoma's industrial tideflats as pictured on March 25, 1922. Visible are the sprawling St. Paul & Tacoma Lumber Co. and the Washington Parlor Furniture Co. at far left and the Pacific Lumber & Millwork Co. in center. They were at the foot or end of the 11th St. Bridge (now Murray Morgan Bridge). TPL-5731; G91.-017
St. Paul & Tacoma Lumber Co. (Tacoma); Washington Parlor Furniture Co. (Tacoma); Pacific Lumber & Millwork Co. (Tacoma);
On May 9, 1922, a steam cargo ship was pictured docked at the Tidewater Mill, where it was taking on a shipment of lumber. The Mill was located on the east side of the Hylebos Waterway, near the end of 11th St. It was opened in 1918 and had a capacity of 100,000 logs a day. The mill was built on wetlands which were filled for the construction of the mill. Its greatest advantage was its frontage on 750 feet of deep water, allowing the loading of several vessels at a time. (TDL 12/22/1918, Pg. B-8)
These massive logs are being transported on Northern Pacific flatcars to the St. Paul & Tacoma Lumber Co. yard on May 13, 1922. Railroad tracks intersect at this particular location. G44.1-103
Lumber industry--Tacoma--1920-1930; Logs; St. Paul & Tacoma Lumber Co. (Tacoma); Northern Pacific Railway Co. (Tacoma); Railroad cars--Tacoma--1920-1930; Railroad tracks--Tacoma--1920-1930;
Sawmill operations. View of St. Paul & Tacoma's modern sawmill, recently placed in operation, as pictured on May 21, 1922. Machinery and tracks in foreground. The new mill was the latest of improvements enacted by the lumber firm. G36.1-034 (TDL 5-23-22, p. 7-article)
Lumber industry--Tacoma--1920-1930; St. Paul & Tacoma Lumber Co. (Tacoma); Sawmills--Tacoma--1920-1930; Machinery;
Mill operations. Interior view of machinery and wood at St. Paul & Tacoma's new sawmill on May 21, 1922. Mill "C" started operation the following day. It was the latest of improvements done by the company. The new mill had a capacity of 200,000 feet of lumber every eight hours. It was electrically operated throughout and had all the latest safety devices. (TDL 5-23-22, p. 7-article)
Lumber industry--Tacoma--1920-1930; St. Paul & Tacoma Lumber Co. (Tacoma); Machinery; Sawmills--Tacoma--1920-1930;
Sawmill operations. There are no walls in this part of St. Paul & Tacoma Lumber Co.'s new sawmill but an open beamed ceiling provides cover for the tracks below. This was Mill "C" which would start operating on May 22, 1922. St. Paul & Tacoma had spent much money in getting their plant in the best condition. The entire plant was modernized, Mills "A" and "B" electrically updated, and new docks and additional warehouses built. G36.1-035 (TDL 5-23-22, p. 7-article)
Lumber industry--Tacoma--1920-1930; Sawmills--Tacoma--1920-1930; St. Paul & Tacoma Lumber Co. (Tacoma);
This is one of Tacoma's shipyards in the Tideflats in a photograph taken on September 8, 1922. A crane and stacks of lumber are visible across from the large building in this deteriorated print. G36.1-011
These are believed to be buildings in an unidentified Tacoma shipyard. This September, 1922, photograph also shows the nearness of railroad tracks to the buildings to make it easier for lumber to be transported. G36.1-085 (print has deteriorated)
Four delegates to the 13th annual Pacific Logging Congress Convention posed for photographer Marvin Boland on October 28, 1922. The men have removed their hats for this picture. The earlier conventions of the Pacific Logging Congress had a mixture of delegates representing management and workmen. All were interested in the latest logging techniques and equipment to further improve their industry. The 1922 convention saw representatives from all the Pacific Coast states and British Columbia in attendance at the four-day session in Tacoma. G75.1-135
At a time when timber was king, and logs of this size were not unusual, thirteen delegates to the 13th annual Pacific Logging Congress Convention were able to balance themselves on top of large cut logs in this late October of 1922 photograph - with room to spare. A special excursion train left Tacoma's Union Station on Saturday, October 28, 1922, for a day trip to the St. Paul & Tacoma Lumber Co. camp at Kapowsin. There the many delegates viewed up-to-date methods of logging by high leads and lidgerwood skidders. The convention took place October 25-28, 1922, and attracted some 500 representatives of the logging industry. G75.1-138 (TDL 10-23-22, p. 5-article; TDL 10-25-22, p. 1-article; TDL 10-26-22, p. 1-article)
