ca. 1918. The Puget Mill Company Hall in Port Gamble, circa 1918. The Company Hall was built in 1907 and designed by the Seattle architecture firm of Bebb and Mendel. It was located across Rainier Ave. from the General Store. The hall was intended to serve as a location for meetings, athletic events, socials and worship. The first floor contained offices for the doctor and dentist, a barber shop, telegraph office and Post Office. The second floor served as a meeting room, theater, movie house and dance hall. The building is still in use as a Post Office and rents office space. (Historylink.org) Boland #P-4

Lumber industry--Port Gamble; Puget Mill Co. (Port Gamble); Post offices--Port Gamble; Community centers--Port Gamble;

ca. 1918. The home at the top right of the picture is the Walker-Ames house in Port Gamble, circa 1918. The structure on the left is unidentified. Port Gamble was the company town owned by the Puget Mill. A hierarchy developed in company housing, with the Superintendent receiving the largest house on the highest ground with the best view of the mill. The original Superintendent's home burned down in 1885 and was replaced by this Queen Anne structure built in 1888. Superintendent Edwin Ames was single at the home's completion and did not need such a large structure, so the home was occupied by master mechanic William Walker, brother of original general manager and shareholder Cyrus Walker, and his family. Ames married the Williams daughter and the two families shared the house until 1900. (TNT 12/31/1972, pg. B-5, Historylink.org) G73.1-032

Lumber industry--Port Gamble; Puget Mill Co. (Port Gamble); Walker-Ames House (Port Gamble);

Log on shute. This log on a shute at an unidentified sawmill was photographed in mid-August of 1919. TPL-8085; G36.1-015

Logs;

An early logging truck, used by Wilson Logging Co. to bring in logs, was photographed in August of 1919. The early motor trucks offered an economical alternative to railway logging. Despite the cost of constructing roads, the trucks were a cheaper, faster and more practical way to move the logs. They were a common sight by the 1920s. They usually were underpowered, had an open cab and hard rubber tires, but they could go places that locomotives could not. There was a C.C. (Chan) Wilson Lumber Co. located in Hudson, just west of Rainier, Oregon. G75.1-032 (website for the Museum at Campbell River www.crmuseum.ca\exhibits)

Lumber industry--1910-1920; Wilson Logging Co.;

On May 9, 1922, a steam cargo ship was pictured docked at the Tidewater Mill, where it was taking on a shipment of lumber. The Mill was located on the east side of the Hylebos Waterway, near the end of 11th St. It was opened in 1918 and had a capacity of 100,000 logs a day. The mill was built on wetlands which were filled for the construction of the mill. Its greatest advantage was its frontage on 750 feet of deep water, allowing the loading of several vessels at a time. (TDL 12/22/1918, Pg. B-8)

Tidewater Mill Co. (Tacoma); Lumber industry--Tacoma--1920-1930; Cargo ships--1920-1930;

Four delegates to the 13th annual Pacific Logging Congress Convention posed for photographer Marvin Boland on October 28, 1922. The men have removed their hats for this picture. The earlier conventions of the Pacific Logging Congress had a mixture of delegates representing management and workmen. All were interested in the latest logging techniques and equipment to further improve their industry. The 1922 convention saw representatives from all the Pacific Coast states and British Columbia in attendance at the four-day session in Tacoma. G75.1-135

Pacific Logging Congress; Meetings--Tacoma--1920-1930; Lumber industry--Tacoma--1920-1930; Logs;

At a time when timber was king, and logs of this size were not unusual, thirteen delegates to the 13th annual Pacific Logging Congress Convention were able to balance themselves on top of large cut logs in this late October of 1922 photograph - with room to spare. A special excursion train left Tacoma's Union Station on Saturday, October 28, 1922, for a day trip to the St. Paul & Tacoma Lumber Co. camp at Kapowsin. There the many delegates viewed up-to-date methods of logging by high leads and lidgerwood skidders. The convention took place October 25-28, 1922, and attracted some 500 representatives of the logging industry. G75.1-138 (TDL 10-23-22, p. 5-article; TDL 10-25-22, p. 1-article; TDL 10-26-22, p. 1-article)

Pacific Logging Congress; Meetings--Tacoma--1920-1930; Lumber industry--Tacoma--1920-1930; Logs;

Permits were taken out in late December of 1922 to construct a new lumber yard at 6030 South Tacoma Way (then called South Union Avenue). Fairhurst Lumber Co. would open for business in early 1923. G36.1-084; Bu12,859

Fairhurst Lumber Co. (Tacoma); Lumber industry--Tacoma--1920-1930;

On February 19, 1924, this giant 40-foot log was successfully loaded onto a Chicago, Milwaukee & St. Paul railroad freight car by employees of the St. Paul & Tacoma Lumber Co. The log, measuring 72 inches in diameter, would be a prime exhibit when shown in the East and Midwest the following summer. The sheer size of the log would remind viewers that lumber from Tacoma mills came from logs similar to the one displayed. TPL-2375; G44.1-093

Lumber industry--Tacoma--1920-1930; Logs; St. Paul & Tacoma Lumber Co. (Tacoma); Railroad freight cars--Tacoma; Chicago, Milwaukee & St. Paul Railroad Co. (Tacoma);

Piles of logs waiting to be removed via railroad flatcars from a West Fork Logging Co. site in March of 1924. G75.1-088

Logs; West Fork Logging Co.;

Logging operations in the woods, in the Seabeck, Washington, area. West Fork Logging Co. apparatus on railroad tracks photographed on March 23, 1924. L.T. Murray was the president of the firm. Mr. Murray would move his logging operation to Lewis County in 1927. G75.1-089 (Additional information provided by a reader)

West Fork Logging Co.; Lumber industry--1920-1930;

On March 23, 1924, West Fork Logging Co. employees posed near the company's steam donkey on a sled. The donkeys were a replacement for the horse and oxen power formerly used to pull logs from the woods. This photograph was probably taken in logging areas near Seabeck where the company was then based. Logging operation would move to Lewis County three years later. G75.1-033 (for an earlier view of a steam donkey, see B2726) (Additional information provided by a reader)

West Fork Logging Co.; Lumber industry--1920-1930; Steam donkeys; Donkey engines;

Side view of Chicago, Milwaukee, St. Paul & Pacific Railroad Co. locomotive #9505 showing wheels. Photograph was taken on January 23, 1925. G44.1-043

Railroad locomotives; Chicago, Milwaukee, St. Paul & Pacific Railroad Co.;

Four unidentified men gaze at a long line of railroad flat cars stacked with mahogany logs on May 1, 1925. The log train was bound for the Buffelen Lumber & Mfg. Co. The logs had arrived at the Port of Tacoma on the "Wheatland Montana" and were a product of the Philippines. The arrival of the logs marked a transition to direct transactions between the overseas grower and a Tacoma manufacturer. Prior to this, mahogany used in fine furniture, cabinets and other uses was brought here in board form. G36.1-030 (TNT 5-4-25, p. 6)

Logs; Railroad cars--Tacoma--1920-1930; Shipping--Tacoma--1920-1930;

Henry Mill in Old Town. A new and very modern mill opened in Old Town on July 20, 1925, located on the waterfront at 3001 North Starr St. Henry Mill & Timber Co. would remain in business there until 1945 when it was taken over by the Tacoma Lumber Fabricating Co. During WWII, Henry Mill became active in prefabricated structures for the military. They specialized in bridges and hangars. TPL-2048; G36.1-143B

Henry Mill & Timber Co. (Tacoma); Mills--Tacoma--1920-1930; Lumber industry--Tacoma--1920-1930; Railroad tracks--Tacoma--1920-1930;

Close-up of burnt timber at the Mineral Lake Logging Co.'s Camp 17. Photographer Boland ventured out to the remote logging camp located in north central Lewis County on September 3, 1926, to document the damage that fire had caused to timberlands. Burned sections of cut timber are piled haphazardly on the ground, obscuring many tree stumps.

Mineral Lake Logging Co. Camp 17; Fires; Tree stumps; Logs; Lumber industry--Washington--1920-1930;

Members of the Washington Co-op Egg & Poultry Association are aboard a small Great Northern locomotive which is pulling three boxcars presumably packed with eggs for the 1930 Western Washington Fair. G74.1-034

Railroad locomotives; Railroad freight cars; Washington Co-op Egg & Poultry Association (Tacoma);

St. Regis logging operations, location unknown, in May of 1936. A heavy duty truck with five coils of wire/chain/rope hanging on one side is mired off the dirt road. Many logs have already been downed and a "donkey" is billowing steam. G75.1-043

Lumber industry--1930-1940; St. Regis Paper Co.; Trucks--1930-1940; Logs; Donkey engines;

Timber on St. Regis land as photographed in August of 1936. Some trees have already been felled. G75.1-097

St. Regis Paper Co.; Trees; Lumber industry--1930-1940;

1936 daily operations at St. Regis. A series of photographs were taken in two days of a St. Regis facility by the Boland studios in December of 1936. It is believed that the plant was the Tacoma location at 801 Portland Ave. Many internal shots were taken including the above which appears to be a large steel covered vat. The St. Regis Kraft Co. plant had undergone a months-long remodeling which included new machinery and fixtures. All of this was to transform the outdated facility into a modern plant so that it could produce 60,000 tons of bleached pulp per year. (T.Times 10-14-36, p. 5-article; T. Times 11-25-36, p. 5-article) G37.1-031

St. Regis Paper Co. (Tacoma)--1930-1940; Paper industry--1930-1940; Lumber industry--1930-1940; Mills--Tacoma--1930-1940;

1936 daily operations at St. Regis. Interior view of a St. Regis Paper Co. facility, believed to be the Tacoma plant located at 801 Portland Ave. in 1936. Steel beams and steel or concrete chutes in sight. St. Regis employed 845 men to remodel its Tacoma location in order to transform it into a modern plant for the production of 60,000 tons of bleached pulp per year. New machinery was purchased to handle 25,000 short logs per hour and electric saws and machines to bark logs were also included. Tacoma's prime location near rail, water and (later) highway access made it a valuable asset for manufacturers in the industrial Tideflats. (T.Times 10-14-36, p. 5-article; T. Times 11-25-36, p. 5-article)

St. Regis Paper Co. (Tacoma)--1930-1940; Paper industry--1930-1940; Lumber industry--1930-1940; Mills--Tacoma--1930-1940;

1936 Daily operations at St. Regis. A St. Regis employee is shown on December 21, 1936, loading stacks of the company's pulp via forklift. Another tall stack of pulp is already on a raised pallet. This may be the St. Regis Tacoma facility located at 801 Portland Ave. which had recently undergone a $1,000,000 modernization. TPL-6803; G37.1-055

St. Regis Paper Co. (Tacoma)--1930-1940; Paper industry--1930-1940; Lumber industry--1930-1940; Hoisting machinery; Mills--Tacoma--1930-1940;

1936 daily operations at St. Regis. Three employees of St. Regis Paper Co. stand behind a large cut log whose bark may have already been stripped. Although the particular St. Regis plant was not identified, this may have been the Tacoma plant located at 801 Portland Ave. The plant had purchased new machinery including machines to bark logs before going to regular pulp chippers and was undergoing transformation into a modern plant. By late November of 1936, the newly modernized Tacoma plant had commenced operations with a crew of 250. Eventually the plant would operate on a 24-hour day with four staggered shifts of eight hours. The modernization allowed for production of 60,000 tons of bleached pulp per year. TPL-2453; G36.1-023 (T.Times 10-14-36, pl 5-article; T. Times 11-25-36, p. 5-article)

St. Regis Paper Co. (Tacoma)--1930-1940; Paper industry--1930-1940; Lumber industry--1930-1940; Logs; Mills--Tacoma--1930-1940;

1936 daily operations at St. Regis. Interior view of newly expanded and modernized St. Regis mill, presumed to be in Tacoma, as seen on December 21-22, 1936. The company was proceeding into the bleached pulp business and had to extensively update their facility at 801 Portland Ave. in the Tideflats. St. Regis had previously manufactured unbleached pulp but the demand for the bleached product was rising, necessitating modernization. It would take another 60 days or so for the bleaching unit to be ready so the company would continue to produce unbleached pulp. G37.1-063 (T. Times 10-14-36, p. 5-article; T. Times 11-25-36, p. 5-article)

St. Regis Paper Co. (Tacoma)--1930-1940; Paper industry--1930-1940; Lumber industry--1930-1940; Mills--Tacoma--1930-1940; Machinery;

A St. Regis employee maneuvers a lift to hoist stacks of pulp at the big pulp plant in late December of 1936. The St. Regis Kraft Co. had resumed operations with a crew of 250 after months of modernization and expansion. Unbleached pulp would be produced until the new bleaching unit was ready in 1937. G37.1-056 (T.Times 10-14-36, p. 5-article; T.Times 11-25-36, p. 5-article)

St. Regis Paper Co. (Tacoma)--1930-1940; Paper industry--1930-1940; Lumber industry--1930-1940; Mills--Tacoma--1930-1940; Hoisting machinery;

Workers at St. Regis Kraft Co. are in the process of wrapping and weighing stacks of pulp for shipment in this February 5, 1937, photograph. St. Regis' Tacoma plant had undergone a $1,000,000 modernization project in order to manufacture bleached pulp. New machinery was brought in and the plant was reopened in late December of 1936 to provide jobs for hundreds of Tacoma residents. G37.1-069

St. Regis Paper Co. (Tacoma)--1930-1940; Paper industry--1930-1940; Lumber industry--1930-1940; Mills--Tacoma--1930-1940; Machinery;

Medusa on the ways. The USS Medusa, a $4,000,000 repair ship for the Pacific fleet, is pictured prior to launching at the Bremerton Navy Yard in April of 1923. The "Medusa," the first ship of her kind to be built on the Pacific coast, had a displacement of 10,000 tons. Her launching was rather unusual, as she did not not slide down the ways into water as normal but instead, water was poured into the construction dock where she was built. When floated, she was towed to her new berth and the dock emptied. She was 483-feet, 9 inches long and resembled a huge ocean liner except for the small guns mounted on her. The USS Medusa was launched on April 16, 1923, with Mrs. Burns Poe of Tacoma acting as sponsor. G37.1-121 (TNT 4-4-23, p. 17; TDL 4-7-23, p. 1-article; TDL 4-17-23, p. 1-article)

Boat & ship industry--Bremerton--1920-1930; Launchings--Bremerton--1920-1930;

Henry Mill & Timber Company crane at 3001 N Starr ST, Tacoma

Industries; Henry Mill & Timber Company; Cranes; Ruston Way;

Stacking lumber with the help of a stacker made by Star Iron & Steel.

Industries; Lumber; Star Iron & Steel; Machinery;

Steel plate girder manufactured by Star Iron & Steel for the Masonic Temple at 47 Saint Helens Ave, Tacoma.

Industries; Star Iron & Steel; Construction; Masonic Temple;