ca. 1973. Standing over a hundred feet tall is this unidentified supporting structure at Kaiser Aluminum's Tideflats plant. Its size is apparent compared to the man standing at the foot of one of the supports. Even the truck nearby appears miniscule. Photograph ordered on December 19, 1973, by Puget Sound Fabricators, Seattle.

Kaiser Aluminum & Chemical Corp. (Tacoma); Aluminum industry--Tacoma--1970-1980;

Interior of new aluminum rod mill at Kaiser Aluminum, 3400 Taylor Way, on November 1, 1968. This view is of one-half of Potline #4 and a cart loaded with "channels" which were lowered by crane into a slot just inside the ore hoppers visible on top of each "pot" or reduction cell. The new rod mill was nearly completed and ready for operation.The first rod would be formed in a test run on December 12, 1968. Molten aluminum would be processed into 3/8-inch rods at Tacoma's local mill and then shipped to San Leandro, California, for drawing into electrical wiring. Kaiser had reopened its Tacoma facilities in 1964 after a six-year closure and had steadily expanded since then. It was to permanently close in 2002. Photograph ordered by Kaiser Engineers. (TNT 12-13-68, C-18) (Additional information provided by a reader)

Kaiser Aluminum & Chemical Corp. (Tacoma); Aluminum industry--Tacoma--1960-1970; Industrial facilities--Tacoma--1960-1970;

New aluminum rod mill under construction. Kaiser Aluminum & Chemical Corp. was building a new rod mill in 1968; it would be ready for operation in December of that year. Once fully functional, the completely automated mill would produce rod at a rate of 1,800 feet per minute. Kaiser was undergoing a period of expansion where a new 500-foot stack and the rod mill were built, a second alumina dome with 100,000-ton capacity would be completed in 1969. Photograph ordered by Kaiser Engineers. (TNT 12-13-68, C-18)

Kaiser Aluminum & Chemical Corp. (Tacoma); Aluminum industry--Tacoma--1960-1970; Industrial facilities--Tacoma--1960-1970;

New aluminum rod mill under construction. Construction progresses on the new Kaiser Aluminum's rod mill on 3400 Taylor Way in early November, 1968. Covers have now been placed on the two small dome-containers. It is possible that these containers would hold the molten aluminum that would be used to manufacture the 3/8th-inch rods. Earlier photograph taken on October 18, D154922, Image 4, shows them uncovered. The mill would form its first rod in a test run on December 12, 1968. Photograph ordered by Kaiser Engineers. (TNT 12-13-68, C-18)

Kaiser Aluminum & Chemical Corp. (Tacoma); Aluminum industry--Tacoma--1960-1970; Industrial facilities--Tacoma--1960-1970;

Smoke drifts from the new 500-foot stack at the Kaiser Aluminum plant on Tacoma's Tideflats in late October, 1968. Kaiser was undergoing a period of expansion that would see a new aluminum rod mill open for production in December of 1968. Hylebos Waterway is adjacent to the plant on left side of photograph. Photograph ordered by Kaiser Engineers.

Kaiser Aluminum & Chemical Corp. (Tacoma); Aluminum industry--Tacoma--1960-1970; Industrial facilities--Tacoma--1960-1970; Hylebos Waterway (Tacoma); Aerial views;

Exterior of new aluminum rod mill at Kaiser Aluminum. Kaiser gradually phased in their new aluminum rod mill with its first rod being formed in a test run in December, 1968. The completely automated mill would produce rod at a rate of 1,800 feet a minute. Kaiser would produce the first semi-fabricated aluminum product for Tacoma. Photograph ordered by Kaiser Engineers, Inc. (TNT 12-8-68, A-7)

Kaiser Aluminum & Chemical Corp. (Tacoma); Aluminum industry--Tacoma--1960-1970; Industrial facilities--Tacoma--1960-1970;

Kaiser Aluminum plant aerials. Kaiser Aluminum, located at 3400 Taylor Way in the Tideflats, had resumed production in 1964 after being closed for six years. They were still expanding in 1968 when the above aerial photograph was taken. Hylebos Waterway and Northeast Tacoma in background. Photograph ordered by Kaiser Engineers. TPL-4741

Kaiser Aluminum & Chemical Corp. (Tacoma); Aluminum industry--Tacoma--1960-1970; Industrial facilities--Tacoma--1960-1970; Aerial views; Hylebos Waterway (Tacoma);

Closer aerial view of Kaiser's Tacoma plant located at 3400 Taylor Way in the industrial Tideflats. Taken on October 30, 1968, photograph emphasizes the height of what is believed to be the 500-foot stack recently constructed. Hylebos Waterway in background. Photograph ordered by Kaiser Engineers. TPL-6580

Kaiser Aluminum & Chemical Corp. (Tacoma); Aluminum industry--Tacoma--1960-1970; Industrial facilities--Tacoma--1960-1970; Aerial views; Hylebos Waterway (Tacoma);

Storage tanks at Kaiser Aluminum are massive in nature; they dwarf the Canadian National Railroad boxcars that are motionless in front of them. Olin Corporation Aluminum Plant was the first occupant of the 3400 Taylor Way site; it was sold to Kaiser Aluminum in late 1946. Kaiser spent nearly three million dollars in 1952 to expand its plant, thereby increasing aluminum production accordingly. Easy access to rail transportation made delivery of its product fast and efficient. Photograph ordered by Kaiser Aluminum.

Kaiser Aluminum & Chemical Corp. (Tacoma); Aluminum industry--Tacoma--1950-1960; Storage tanks--Tacoma; Railroad freight cars--Canada;

A view across the Tideflats and adjacent pond shows the expanded Kaiser Aluminum plant in November, 1957. Built originally for Olin Corporation in 1942, and purchased by Kaiser four years later, heavy demand for aluminum products post-war made expansion of the plant necessary. Kaiser spent nearly three million dollars in 1952 to improve their Tacoma plant facilities which led to a large increase in aluminum production. Photograph ordered by Kaiser Aluminum.

Kaiser Aluminum & Chemical Corp. (Tacoma); Aluminum industry--Tacoma--1950-1960;

ca. 1956. In 1956, an employee at Tacoma's Kaiser Aluminum & Chemical Corp. plant used an overhead crane to hold a crucible of molten aluminum and pour the liquid metal into a casting mold. The Tacoma plant was originally built in 1942 for the Olin Corporation. Kaiser took over the plant in 1946 and spent over $3 million to expand and modernize the facility in 1952. It was an aluminum reduction facility. It produced pig aluminum from treated ore. The pigs weighed either 50 or 1,000 pounds. Most were sent by rail to Kaiser's Rolling mill at Trentwood, near Spokane, where they were converted into sheets and products. Some went directly to the more than 500 independent aluminum fabricators in the Pacific Northwest, who consumed the pigs directly in the operation of their own remelt and rolling mills. Kaiser closed their Tacoma plant on the tideflats in 2000. (Kaiser Aluminum News, August 1956)

Kaiser Aluminum & Chemical Corp. (Tacoma); Aluminum industry--Tacoma--1950-1960;

ca. 1956. Kaiser Aluminum plant. Molten metal is being poured from a vat into a mold to form "pigs." The Tacoma plant was an aluminum reduction facility. It produced the pig aluminum from treated ore. Each "pig" weighs 50 pounds and contains higher that 99% pure aluminum. The Bonneville Power Administration provided the abundant power needed to produce the metal by electrolysis. (Kaiser Aluminum News, August 1956)

Kaiser Aluminum & Chemical Corp. (Tacoma); Aluminum industry--Tacoma--1950-1960;

ca. 1956. Kaiser Aluminum plant. The Tacoma plant was located on the Tideflats, about 5 miles north of downtown Tacoma. Its proximity to the Bonneville Power Administration made it the perfect location for producing aluminum from ore by electrolysis. Dissolved in solution in long lines of reductions cells ("pots"), alumina is subjected to electrical current. Chemicals recombine, aluminum separates from its oxygen and settles as pure metal. Tacoma was part of a "mill to mill" operation, the alumina was shipped by rail in from Baton Rouge, La., and the finished aluminum was railed out to Kaiser's Trentwood rolling mill 300 miles to the East. (Kaiser Aluminum News, August 1956)

Kaiser Aluminum & Chemical Corp. (Tacoma); Aluminum industry--Tacoma--1950-1960;

ca. 1956. Kaiser Aluminum plant. The Tacoma plant was a reduction plant, where treated ore (alumina) was subjected to an electrical current, dividing the oxygen from the pure metal (aluminum.) The plant employed approximately 500 workers, who worked on a 24 hour, around the clock basis. Its payroll was over $2,000,000 a year, and it purchased more than $1,300,000 of Northwest materials, supplies and services in a year. It was part of the Kaiser Industries conglomerate founded by Henry J. Kaiser, a diverse group of businesses that included paving, dam construction, ship building, the production of aluminum, steel, cement and other building materials, automobile production and Kaiser foundation heath care. (Kaiser Aluminum News, August 1956 and "The Kaiser Story")

Kaiser Aluminum & Chemical Corp. (Tacoma); Aluminum industry--Tacoma--1950-1960;

ca. 1956. Kaiser Aluminum plant. The new 420 foot potline at the Tacoma reduction plant; the result of a $2,000,000 expansion. The line contains 18 new "super size" reduction cells that will increase aluminum production by 15%. The Bonneville Power Administration will provide the power to reduce the ore to pure metal by electrolysis. Dissolved in solution in long lines of reduction cells ("pots",) alumina ore is subjected to electrical current. The chemicals recombine, the aluminum separates from the oxygen and settles as pure metal, aluminum. (Kaiser Aluminum News, August 1956)

Kaiser Aluminum & Chemical Corp. (Tacoma); Aluminum industry--Tacoma--1950-1960;

Kaiser Aluminum; exterior of new pot room building. This reduction plant will become the newest facility to receive power when the the switches are thrown to 18 new "super size pots" or electrolytic reduction cells. Power will be supplied by the Bonneville Power Administration on an interruptible basis. The 18 extra "pots" will boost the plant's production by 10 million pounds annually. (TNT 4/16/1956, pg. 21)

Kaiser Aluminum & Chemical Corp. (Tacoma); Aluminum industry--Tacoma--1950-1960;

Kaiser Aluminum; new pot room building. Checking cathode bus, arc building. The new building contained 18 new "super size" reduction pots or electrolytic cells. These cells would boost the plant's annual production by more than 10 million pounds and increase payroll by more than $100,000. This addition will bring the corporate primary aluminum capacity in the Northwest to 429 million pounds annually. As the 5th largest employer in the state, Kaiser paid more than 31 1/2 million dollars in wages in 1955 at their Spokane and Tacoma plants. (TNT 4/16/1956, pg. 21)

Kaiser Aluminum & Chemical Corp. (Tacoma); Aluminum industry--Tacoma--1950-1960;

Kaiser Aluminum; new pot room building. Dumping anode paste, arc building. Kaiser's newest facility contained 18 large "pots" or electrolytic cells, which would add 10 million pounds annually to plant production. Power would be supplied to the cells by the Bonneville Power Administration on a interruptible basis. (TNT 4/16/1956, pg. 21)

Kaiser Aluminum & Chemical Corp. (Tacoma); Aluminum industry--Tacoma--1950-1960;

Kaiser Aluminum; Arc building, looking southeast. The Kaiser Aluminum plant was located about 5 miles north of downtown Tacoma. It had been obtained in 1947 by the huge Kaiser business conglomerate built by Henry J. Kaiser. It was purchased from the Defense Plant Corporation. Kaiser modernized the closed plant and began a series of expansions. In 1956, a $2,000,000 expansion was complete with the creation of 18 new "super size" reduction cells. The improvement also included the erection of a mill-type building to house the 420 ft. potline, office and laboratory buildings, an added electric substation and installation of aluminum bus bars and auxiliary electrical equipment. (Kaiser Aluminum News, August 1956)

Kaiser Aluminum & Chemical Corp. (Tacoma); Aluminum industry--Tacoma--1950-1960;

Kaiser Aluminum; new pot room; Interior view, Arc building. A man drives a modernistic piece of equipment, a mechanical arm with a tractor base. This new 420 foot potline at the Tacoma plant has 18 "super-size" reduction cells, increasing primary aluminum production by 15%. The Tacoma plant is a reduction plant, it uses power from hydro electric sources to reduce alumina to aluminum. In 1947, Kaiser bought the Tacoma plant from the Defense Plant Corporation which had operated it as a war emergency plant and closed it after VJ day. Its proximity to plentiful electric power, supplied by the Bonneville Power Administration, made it the perfect location for creating aluminum "pigs" by electrolysis. The plant on the Tideflats ran on a 24 hour, around the clock basis. (Kaiser Aluminum News, August 1956)

Kaiser Aluminum & Chemical Corp. (Tacoma); Aluminum industry--Tacoma--1950-1960;

Kaiser Aluminum & Chemical Corp. At Kaiser's Tacoma reduction plant, ore is carefully analyzed. Dick Hildebrandt, plant chemist, performs an analysis of petroleum pitch, used in the production of carbon anodes for the electrolytic aluminum reduction process. One of the plant's largest regional purchases in 1954 was $214,000 worth of petroleum pitch. (TNT 5/16/1955, pg. 11)

Kaiser Aluminum & Chemical Corp. (Tacoma); Aluminum industry--Tacoma--1950-1960; Hildebrandt, Dick;

Kaiser Aluminum & Chemical Corp. Pig aluminum, stacked and banded, is being loaded onto railroad cars for transportation to Kaiser's Trentwood, Wa. rolling mill to be made into a finished product. The Tacoma plant was an aluminum reduction facility. It produced the pig aluminum from treated ore. Each "pig" weighs 50 pounds and contains higher that 99% pure aluminum. The plant capacity in 1953 was 64 1/2 million pounds a year. (TNT 9/5/1955, pg. C-8)

Kaiser Aluminum & Chemical Corp. (Tacoma); Aluminum industry--Tacoma--1950-1960;

On October 27, 1948, Permanente Metal Corporation employees, left to right, Charlotte Thorestad, C.P. (Pat) Love (plant manager) and Darlene O'Brien sat surrounded by a sea of iced cupcakes marked with a "P" and decorated with a single candle. Permanente's aluminum reduction plant at 2400 Taylor Way was celebrating its first year of production of Kaiser Aluminum with a "Family Day" Open House. Employees along with 1,500 friends, families and relations were the guests of management. They observed the step by step process of making aluminum and ate hot dogs cooked on a 500 lb. "pig" of aluminum, sandwiches, cupcakes and punch. The plant had been previously operated during World War II by the Olin Corporation. After its purchase by Kaiser, it became one of six aluminum plants operated by the company. The other plants were located at Mead and Trentwood Washington (near Spokane), Baton Rouge La., Newark Ohio and San Jose Ca. The Tacoma plant was permanently closed in 2002 and later demolished. (TNT 10/28/1948, p.1)

Permanente Metals Corp. (Tacoma)--Employees; Aluminum industry--Tacoma--1940-1950; Employees--Tacoma--1940-1950; Baked products--Tacoma--1940-1950; Love, Charles P.; O'Brien, Darlene; Thorestad, Charlotte; Anniversaries--Tacoma--1940-1950;

Permanente's First Anniversary, Permanente Metals, Bill Gorman. A crowd of employees and their families watch James Condos, a caster at the plant, demonstrate pouring molten aluminum from a large ladle into a form for pig aluminum. More than 1,500 visitors crowded into the plant October 27, 1948, to celebrate the plant's first year of operation under Kaiser. They saw the step-by-step processes that went into making aluminum by touring the potrooms, rectifier stations, the machine shop, blacksmith shop and the casting room. (T.Times, 10/18, 1948, -.1)

Permanente Metals Corp. (Tacoma)--Employees; Aluminum industry--Tacoma--1940-1950; Laborers--Tacoma--1940-1950; Families--Tacoma--1940-1950; Anniversaries--Tacoma--1940-1950;

Permanente's First Anniversary, Permanente Metals, Bill Gorman. A family enjoys hot dogs during the celebration at Permanente on October 27, 1948. The older girl sits on a stack of aluminum pigs that have been produced at the plant. The woman holds a baby with one arm and her hot dog in her other hand. The weiners for the event were fried on one of the hot 500 pound pigs of aluminum at the plant. (T.Times, 10/28/1948, p.1)

Permanente Metals Corp. (Tacoma)--Employees; Aluminum industry--Tacoma--1940-1950; Laborers--Tacoma--1940-1950; Families--Tacoma--1940-1950; Frankfurters--Tacoma--1940-1950;

Leo Olsen lost the use of his legs to infantile paralysis when he was 9 years old, but he was determined to be part of WWII. Although a tailor by trade, and a pianist, he found work at the Olin Coporation aluminum plant, on the tide flats, running one of the giant cranes that towered over the electric furnaces. This photograph of Mr. Olsen at the controls of his crane was taken in June of 1944 for the Tacoma Chamber of Commerce. (T. Times, 6/27/44, p. 2). Tacoma Chamber of Commerce Manpower publicity at Olin Corp.

Aluminum industry--Tacoma--1940-1950; Handicapped persons--Tacoma; Olin Industries, Inc. (Tacoma); Olsen, Leo;

Permanente Metals would produce 40 million pounds of aluminum per year. The company sells a million and a half pounds of finished aluminum sheets per year o many U. S. firms. Permanente Metals had their headquarters in Oakland, California, Henry Kaiser was the President. View of laborers stacking up pigs, alloyed metals that have been cast into individual ignots (T. Times, 2/12/47, p. 5).

Machinery; Equipment; Laborers--Tacoma; Aluminum industry--Tacoma--1940-1950; Permanente Metals Corp. (Tacoma);

From the evidence provided by this photograph, the security guards at the Kaiser aluminum plant on the Tideflats had a pretty easy life in September of 1947. But one has to wonder what the corporate headquarters for Permanente Metals Corporation thought about the security at their Tacoma plant when they saw this carefully posed picture. The Tacoma plant was only one year old, having been taken over by Permanente Metals Corp. from the Olin Corp. in 1946. (Permanente Metals, Mr. Love) TPL-9603

Permanente Metals Corp. (Tacoma)--Employees; Guards--Tacoma--1940-1950; Private police--Tacoma--1940-1950; Gatehouses--Tacoma--1940-1950; Factories--Tacoma--1940-1950; Aluminum industry--Tacoma--1940-1950;

Permanente Metals, Mr. Love. Olin opened a plant at this location September 1942. In December 1946 the company was sold to Kaiser Aluminum who operated Permanente Metals. The Tacoma plant had its own aluminum reduction plant. Permanente produced "pig" aluminum that was transported to Kaiser plants in Trentwood, near Spokane, to be made into specific grades of aluminum by the addition of other metallic elements such as copper, zinc, silicon, magnesium, manganese, etc. Soda ash from California and alumina from Baton Rough were brought to Tacoma to produce the "pigs". (PMC Annual Report for 1948)

Permanente Metals Corp. (Tacoma)--Employees; Guards--Tacoma--1940-1950; Private police--Tacoma--1940-1950; Gates--Tacoma--1940-1950; Factories--Tacoma--1940-1950; Aluminum industry--Tacoma--1940-1950;

The Tacoma plant of the Permanente Metals Corporation accomplished its first casting of "pigs" from molten metal in November of 1947. Plant employees in the pot room were photographed getting the newly molten metal in the ladle ready to pour into a mold to form pigs. Cast pigs could weigh from fifty and one thousand pounds depending on size and composition. Once cooled, the pigs were stacked on pallets and transported to the rolling mill at Trentwood, located near Spokane, Washington. The pigs from the Mead and Tacoma plant would later be re-melted in furnaces where other metallic elements were added to form standard alloys. Tacoma's Permanente plant produced aluminum in commercial quantities for Henry J. Kaiser's industrial operations. (PMC Annual Report, 1947-1948; T.Times 11-19-47, p. 18-alt. photograph & article).

Aluminum industry--Tacoma--1940-1950; Aluminum; Industrial facilities--Tacoma--1940-1950; Laborers--Tacoma--1940-1950; Permanente Metals Corp. (Tacoma)--Employees;